You can put a soldering iron on Kapton tape and it will not melt. Kapton tape (generically known as polyimide tape) is a cool tool in these cases and better than regular black electrical tape for a number of reasons: I do a lot of work with electronics assembly and disassembly, rewiring, and removing and adding components. To me, the relatively small price difference between the 6 was worth it, but for general work around the house, the 600 should be perfect. The main difference between the T5-1000 and the T5-600 is their maximum voltage ratings, 1000 and 600 VAC respectively. There are two version of the T5, the 1000 and 600 models. It is the first one I grab both at home as well as on my job (I oversee the installation of packaging lines nationwide and, at times, do trouble shooting on pieces of automated equipment). However, this relatively small unit remains my go-to instrument. I have been using a range of Flukes for well over 20 years - everything from a multimeter to a scope meter and other devices. And, for service work for instance, it’s great to be able to check both voltage and amperage of a motor running with one very lightweight, ergonomic tool. For most functioning/troubleshooting, it’s helpful to know first if there is voltage and then if there is current (the garden hose comparison: do I have water pressure? is water flowing?). Perfect for a cramped motor panel or junction box. The fork is also a lot less intrusive and requires less space than the old open-and-clamp design. More importantly, it has a “fork” or “OpenJaw” that can be extended over a current-carrying cable so that it acts like an AMP-clamp, except you don’t have to maneuver or close the jaws, making it quicker and easier to use. I’ve found the T5 to be a bit more robust than the average DMM and very reliable for a device in this price range. The T5 is as reliable as a good, old-fashioned “wiggy” voltage tester, but adds the functionality of a digital multimeter (DMM) and an AMP meter combined. Howard Rheingoldįluke Voltage, Continuity & Current Tester Strip about 3/8 inch on the end of a wire, thread the exposed wire up one of two incredibly tiny slots in the end of the wirewrap tool, put the other tiny slot of the wirewrap tool around the wire it is to be connected to, like the anode or cathode of an LED, then twirl the wirewrap tool in your fingers, leaving a tiny tight spiral of wire wrapped around the connection. To attach fine wires, such as wiring up LEDs into circuits, wire wrap makes soldering unnecessary. This is a beautiful and inexpensive tool a rare mechanical hand tool with precise tolerances. I like mine so much that it never leaves my desk as it serves as miniature whiteboard, mousepad, and DIY repair station. The pro model mat, which I own, also features a nonslip foam backing much like that of a mousepad which when flipped upside down features cutouts that act like cups. Intelligently, iFixit includes a very nice fine-tipped dry-erase marker from Staedtler for quickly jotting down repair notes (that also features a bit of wool on the cap for erasing them, too). Not only does the magnetic surface mean fewer lost screws, but it’s whiteboard surface means I can keep track of what came from where. During this time I’ve found the iFixit’s magnetic mat indispensable. In the past few months I’ve had to repair my iPhone, my digital camera, and my Macbook Pro. Sign up here to get Tools for Possibilities a week early in your inbox. We present these vintage recommendations as is because the possibilities they inspire are new. The tools might be outdated or obsolete, and the links to them may or may not work. Once a week we’ll send out a page from Cool Tools: A Catalog of Possibilities. I haven’ tried fitting one in the above scraper but they are the same size as single-edge blades so would probably fit. The plastic holder that comes with them is a piece of crap (can I say that?). It is the only readily available solvent that does not dissolve plastic. I have to often apply a little naphtha to help it along, and then wipe with naphtha to remove any residue. I had to sharpen the edges with 1000 grit wet-or-dry first, and then they worked fantastically. You can’t use an ordinary razor blade on plastic.These plastic blades work a lot better than a fingernail or butter knife. A much more common problem than decals on windshields, which you deal with, at most, once a year, is those virtually unremovable price stickers and jar labels on PLASTIC. What I did find cool, and useful, was the ScrapeRite Plastic Razor Blades. I don’t see this as anything “cool” or out of the ordinary. Here’s his comment (about the Razor Blade Safety Glass Scraper) He will receive a copy of the Cool Tools Catalog. LarryA2010 wrote our favorite comment of the week. How to remove stickers and jar labels from plastic
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |